Escalo Haak voor Ophangen Trapladder
SKU: 43883272110

Escalo Haak voor Ophangen Trapladder

$25.16 $27.95
Save 10%
No.2 Bestseller on canequilibre.fr >

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 9 - Jul 14

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Escalo Haak voor Ophangen TrapladderMaak doe het zelf projecten nog makkelijker met de innovatieve ladderhanger van Escalo. Dankzij dit slimme ophangsysteem heb je nooit meer een rommelige schuur of garage. De hanger zorgt voor veilige en stabiele opslag van je trap, altijd binnen handbereik. De eenvoudige en snelle installatie maakt het gebruik extra praktisch, terwijl het duurzame stalen ontwerp garant staat voor jarenlang gebruik. Zo bespaar je ruimte n vergroot je de veiligheid in

Maak doe-het-zelf projecten nog makkelijker met de innovatieve ladderhanger van Escalo. Dankzij dit slimme ophangsysteem heb je nooit meer een rommelige schuur of garage. De hanger zorgt voor veilige en stabiele opslag van je trap, altijd binnen handbereik. De eenvoudige en snelle installatie maakt het gebruik extra praktisch, terwijl het duurzame stalen ontwerp garant staat voor jarenlang gebruik. Zo bespaar je ruimte én vergroot je de veiligheid in je werkplaats of thuis.

Waarom kiezen voor de Escalo ladderhanger?

Een opgeruimde werkplek is niet alleen prettig, maar ook veiliger. Met de Escalo ladderhanger berg je je trap gemakkelijk en netjes op, zonder dat hij in de weg staat of om kan vallen.

Ruimtebesparend en praktisch

De hanger maakt optimaal gebruik van de beschikbare ruimte. Door je trap eenvoudig op te hangen, houd je vloerruimte vrij en creëer je een overzichtelijke werkplaats of garage.

Eenvoudige installatie

De ladderhanger is snel en eenvoudig te monteren. Binnen korte tijd heb je een veilige en praktische oplossing om je trap netjes op te bergen.

Duurzaam en betrouwbaar

Gemaakt van stevig staal, gaat de hanger jarenlang mee. Je kunt vertrouwen op een stabiele en robuuste oplossing die bestand is tegen intensief gebruik.

Specificaties

  • Breedte: 31 cm
  • Gewicht: 0,35 kg
  • Materiaal: Staal
  • Garantie: 2 jaar

De voordelen in het kort

  • Ruimtebesparende opslag van je trap
  • Eenvoudig en snel te installeren
  • Duurzame stalen constructie

Klein aandachtspunt

De hanger is ideaal voor standaard trappen; voor zeer zware of extra brede modellen kan een tweede hanger handig zijn voor extra ondersteuning.

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 43883272110

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 2207 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
P
Verified Purchase
Peter Schott
Natrona Heights, US
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
S
Verified Purchase
Steve M.
Bozeman, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Bozeman, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
Boise, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
G
Verified Purchase
Greg
West Palm Beach, US
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024

recommand products

GB HOEKANKER ZWAAR 70X120 EV 70X8
101.09
GB HOEKANKER ZWAAR 60X100 EV 70X8
103.20
GB HOEKANKER ZWAAR 60X100 TV 80X8
118.91
GB GORDINGLAS 71X196 SV 1,5
32.78
GB KRAMPLAAT DUBBELZIJDIG GETAND _26 SV 75
125.97